School of Mathematics, Computer Science & Engineering
  1. About the School
  2. Research
  3. UKACM 2019
  4. Our London location
  5. Athena SWAN
  6. Placements and internships
  7. Engineering & Mathematics scholarships & funding
  8. Computer Science scholarships and funding
  1. Centre for Compressor Technology
  2. Bibliography
School of Mathematics, Computer Science & Engineering

Bibliography

Amosov P.E et al, 1977: Vintovie kompresornie mashinii - Spravochnik (Screw Compression Machines - Handbook), Mashinstroienie, Leningrad

Andreev P.A, 1961: Vintovie kompressornie mashinii (Screw Compression Machines), SUDPROM Leninngrad

Arbon I.M, 1994: The Design and Application of Rotary Twin-shaft Compressors in the Oil and Gas Process Industry, MEP London

Astberg A, 1982: Patent GB 2092676B

Bammert K, 1979: Patent Application FRG 2911415

Bowman J. L, 1983: US Patent 4,412,796

Brasz J. J, Shistla V, Stosic N, Smith, I. K, 2000: 'Development of a Twin Screw Expressor as a Throttle Valve Replacement for Water-Cooled Chillers', XV International Compressor Engineering Conference at Purdue, July 2000. Download the paper (pdf)

Chia-Hsing C, 1995: US Patent 5,454,701

Edstroem S. E, 1974: US Patent 3,787,154

Fleming J. S, Tang Y, 1994: 'The Analysis of Leakage in a Twin Screw Compressor and its Application to Performance Improvement', Proceedings of IMechE, Journal of Process Mechanical Engineering, Vol 209, 125

Fleming J, Yu C. X. and Tang Y. 1994: 'The Influence of Slide Valve on the Thermodynamic Efficiency and Bearing orces of a refrigeration Helical Twin Screw Compressor', Proc. VDI Tagung "Schraubenmaschinen 94", Dortmund VDI Berichte 1135

Fleming J. S, Tang Y, Xing Z. W. and Cook G, 1995: 'The Use of Superfeed in a Refrigeration Plant with a Twin Screw Compressor: An Optimisation Technique for Plant Design', IIR XIX Congress, The Hague, The Netherlands

Fleming J. S, Tang Y, Cook G, 1998: 'The Twin Helical Screw Compressor, Part 1: Development, Applications and Competitive Position, Part 2: A Mathematical Model of the Working process', Proceedings of the IMechEng, Journal of Mechanical Engineering Science, Vol 212, p 369

Fujiwara M, Osada Y, 1995: 'Performance Analysis of Oil Injected Screw Compressors and their Application', Int J Refrig Vol 18, 4

Guerrato D, Nouri J M, Stosic N, Kovacevic A and Arcoumanis C, 2006: 'Cycle Resolved Velocity Measurements within a Screw Compressor', 18th International Compressor Engineering Conference at Purdue, July 2006. Download the paper (pdf)

Guerrato D, Nouri J M, Stosic N, and Arcoumanis C, 2007: 'Flow and Pressure Characteristics within Screw Compressor', Third International Conference on Optical & Laser Diagnostics (ICOLAD), London, 2007

Guerrato D, Nouri J M, Stosic N, Kovacevic A and Arcoumanis C, 2007: 'Flow Development through the Discharge Chamber of a Screw Compressor', International Conference Compressors and Their Systems, London, 2007. Download the paper (pdf)

Guerrato D, Nouri J M, Stosic N, Kovacevic A and Arcoumanis C, 2008: 'Flow Development through the Discharge Chamber of a Screw Compressor', Proc. IMechE, Part E: J. Process Mechanical Engineering, 2008, 222(E4), 211-223

Hanjalic K, Stosic N, 1997: 'Development and Optimization of Screw Machines with a Simulation Model, Part II: Thermodynamic Performance Simulation and Design Optimization', ASME Transactions, Journal of Fluids Engineering, Vol 119, p 664. View the paper

Holmes C, 2006: 'Noise Reduction in Screw Compressors by the Control of Rotor Transmission Error', 18th International Compressor Engineering Conference at Purdue, July 2006. Download the paper (pdf)

Hough D, Morris S. J, 1984: Patent Application GB 8413619

Jacobson, B , 1996: 'Ball-bearing lubrication in refrigeration compressors', Proc 1996 Int Compressor Conf at Purdue, v1, Purdue University, West Lafayette, IND, USA, July 23-26, 1996, pp 103-108

Kasuya K. et al, 1983: US Patent 4,406,602

Kauder K, Harling H. B, 1994: 'Visualisierung der Olverteilung in Schraubenkompressoren (Visualisation of Oil Effects in Screw Compressors)', Proc. VDI Tagung "Schraubenmaschinen 94", Dortmund VDI Berichte 1135

Konka K-H, 1988: Schraubenkompressoren (Screw Compressors) VDI-Verlag, Dusseldorf

Kovacevic A, Stosic N. and Smith I.K, 2000: 'Grid Aspects of Screw Compressor Flow Calculations', 2000 ASME International M.E. Congress, Orlando, FL, November 2000.

Kovacevic A, Stosic N. and Smith I.K, 2001: 'CFD Analysis of a Screw Compressor Performance', IMechE Symposium “Advances of CFD in Fluid Machinery Design”, London June 2001. Download the paper (pdf)

Kovacevic A, Stosic N. and Smith I.K, 2001: 'Analysis of Screw Compressor Performance by Means of 3-Dimensional Numerical Modelling', IMechE Conference on Compressors and Their Systems, London, September 2001.

Kovacevic A, Stosic N. and Smith I.K, 2002: 'Three-Dimensional Modelling of Solid-Fluid Interaction as a Design Tool in Screw Compressors', International Design Conference - DESIGN 2002, Dubrovnik, Croatia, May 14 - 17, 2002.

Kovacevic A, Stosic N. and Smith I.K, 2002: 'Solid-Fluid Interaction in Screw Compressors', XVI International Compressor Engineering Conference at Purdue, July 2002

Kovacevic A, Stosic N. and Smith I.K, 2002: 'Influence of Rotor Deflection upon the Screw Compressor Process', Schraubencompressortagung, Dortmund, September 2002. Download the paper (pdf)

Kovacevic A, Stosic N. and Smith I.K, 2002: 'Numerical Simulation of Fluid Flow and Solid Structure in Screw Compressors', Proceedings of 2002 ASME Congress, Symposium on the Analysis and Applications of Heat Pump and Refrigeration Systems, New Orleans, LA, November 17-22, 2002. Download the paper (pdf)

Kovacevic A, Mujic E, Stosic N, Smith I.K, 2003: 'Advanced Design Tools for Screw Compressors', 2nd DAAAM International Conference on Advanced Technologies for Developing  Countries - ATDC'03 June 25-28, Tuzla, Bosnia and Herzegovina, 2003

Kovacevic A, Stosic N, Smith I.K, 2003: 'The Application of CFD Analysis to the Design of Bifunctional Machines', IMechE International Conference on Compressors and Their Systems, London, September 8-10, 2003

Kovacevic A, Stosic N, Smith I.K, 2003: 'Three Dimensional Numerical Analysis of Screw Compressor Performance', Journal of Computer Methods in Applied Mechanics and Engineering, Vol. 3, no. 2, 2003, pp. 259- 284. Download the paper (pdf)

Kovacevic A, Stosic N, Smith I.K, 2003: 'CFD Analysis of a Screw Compressor Performance', Elder, R.L, Tourlidakis and A, Yates M.K Editors, IMechE Professional Engineering Publishing, 2003

Kovacevic A, Stosic N, Smith I.K, 2004: 'Fluid-Solid Interaction for Extension of Range in Screw Machine Application', Advances of CFD in Fluid Machinery Design, ImechE Seminar, London, November 18 2003

Kovacevic A, Stosic N, Smith I.K, 2004: 'Numerical Simulation of Combined Compressor Expander Machines for Use in High Pressure Refrigeration Systems', Proceedings of SIMS 2004, Technical University of Copenhagen, Sept. 2004. ISBN 87-7475-316-9. Download the paper (pdf)

Kovacevic A, Stosic N, Smith I.K, 2004: 'Fluid-Solid Interaction in the Design of Multifunctional Screw Machines', 8th International Design Conference – Design 2004, Dubrovnik, Croatia, May 17-21, 2004, vol. 2, 1289-1295

Kovacevic A, Stosic N, Smith I.K, 2004: 'Numerical Study of Solid Structure and Fluid Flow Interaction in Screw Compressors', International Journal of Computer Applications in Technology 2004 - Vol. 21, No.4 pp. 148 - 158

Kovacevic A, Stosic N, Smith I.K, 2004: 'Development of Management Interface for Screw Compressor Design Tools', 5th International Conference TMCE 2004, Lausanne , Switzerland, April 14, 2004

Kovacevic A, 2005: 'Boundary Adaptation in Grid Generation for CFD Analysis of Screw Compressors', International Journal for Numerical Methods in Engineering, June 2005, 64:401-426. Download the paper (pdf)

Kovacevic A, Stosic N, Smith I.K, 2006: 'Screw Compressors: Three Dimensional Computational Fluid Dynamics and Solid Fluid Interaction', Monograph, Springer Verlag, Berlin, June 2005, ISBN: 3-540-24275-9

Kovacevic A, Stosic N, Smith I.K, 2006: 'Numerical simulation of combined screw compressor-expander machines for use in high pressure refrigeration systems', Journal of Simulation Modelling Practice and Theory, 14, 1143-1154

Kovacevic A, Mujic E, Stosic N, Smith I.K, 2005: 'Design Integration for Screw Compressors', International Production Conference RIM 2005, Bihac, Bosnia and Herzegovina 2005, CIP 621.1/.9:001.892

Kovacevic A, Mujic E, Smith I.K, Stosic N , 2006: 'Advanced Methods and Tools for Screw Compressor Design', Proceedings of the 6th International Conference TMCE 2006, Ljubljana, Slovenia, April 2006, pp.69-83

Kovacevic A, Mujic E, Smith I.K, Stosic N , 2006: 'Influence of Thermal Dilatation Upon Design of Screw Machine', International Design Conference DESIGN 2006, Dubrovnik - Croatia, May 2006

Kovacevic A, Stosic N, Smith I.K, 2007: 'CFD Integrated Design of Screw Compressors', Journal of Engineering Applications of CFM, 1(2007)2, 96-108

Kovacevic A, Mujic E, Stosic N and Smith I.K, 2007: 'An integrated Model for Performance Calculation of Screw Machines', International Conference Compressors and Their Systems, London, 2007. Download the paper (pdf)

Kovacevic A, Mujic E, Stosic N and Smith I.K, 2008: 'An Integrated Mathematical Model for Twin-Screw Machines', Proceedings of the TMCE 2008, April 21-25, 2008, Izmir, Turkey

Kovacevic A, Stosic N and Smith I.K and Mujic E, , 2008: 'Advances in Numerical and Experimental Investigation of Screw Compressors', ICCR 2008, International Conference on Compressor and Refrigeration, Xian, September 2008

Liebovic H, Stosic N, Smith I.K, 2007: 'Cost Effective Small Scale ORC Systems for Power Recovery from Low Grade Heat Sources', IMECE 2006, ASME Congress, Chicago, November 2006. Download the paper (pdf)

Lee H.T, 1988: US Patent 4,890,992

Litvin F.L, 1956: Teoria zubchatiih zaceplenii (Theory of Gearing), Nauka Moscow, second edition 1968, also Prentice-Hill, Englewood Cliffs, NJ 1994

Lysholm A, 1942: 'A New Rotary Compressor', Proc. I.Mech.E. 150,11

Lysholm A, 1966: 'The Fundamentals of a New Screw Engine', ASME Paper No 66-GT-86

Lysholm A, 1967: US Patent 3,314,598

Margolis D.L, 1978: 'Analytical Modelling of Helical Screw Turbines for Performance Prediction', J.Engr.for Power 100(3)482

McCreath P, Stosic N, Kovacevic A. and Smith I.K, 2001: 'The Design of Efficient Screw Compressors for Delivery of Dry Air', IMechE Conference on Compressors and Their Systems, London, September 2001. Download the paper (pdf)

McCreath P, Stosic N, Smith I.K, Kovacevic A, 2003: 'Proektirovanie effektivniih vintoviih kompressorov dlia podachi suhogo vazduha', Compressors and Pneumatics, Vol 1 pp 2-5, 2003

Meyers K, 1997: 'Creating the Right Environment for Compressor Bearings', Evolution, SKF Industrial Journal, Vol 4, 21

Mujic E, Kovacevic A, Stosic N, Smith I.K, 2005: 'Noise Prediction in Screw Compressors', Proceedings of International Conference on Compressors and their Systems, IMechE London, September 2005. ISBN 0-470-02576-X, pp447-457

Mujic E, Kovacevic A, Stosic N, Smith I.K, 2005: 'Analysis and Measurement of Discharge Port Influence upon Screw Compressor Noise', 9th International Research/Expert Conference Trends in the Development of Machinery and Associated Technology, TMT 2005, Antalya, September 2005

Mujic E, Stosic N, Kovacevic A, Smith I.K, 2007: 'The Influence of Port Shape on Gas Pulsations in a Screw Compressor Discharge Chamber', International Conference Compressors and Their Systems, London, 2007. Download the paper (pdf)

Mujic E, Kovacevic A, Stosic N, Smith I.K, 2007: 'The Influence of the Discharge Port Shape on Screw Compressor Performance and Gas Pulsations', 2008 International Compressor Engineering Conference at Purdue, 14-17 July 2008, Purdue, USA

Mujic E, Stosic N, Kovacevic A, Smith I.K, 2008: 'Reduction of Noise in Screw Compressors', Trends in the Development of Machinery and Associated Technology, TMT 2008, Istanbul, Turkey, 26-30 August, 2008. Download the paper (pdf)

Mujic E, Kovacevic A, Stosic N and I K Smith, 2008: 'The influence of Port Shape on Gas Pulsations in a Screw Compressor Discharge Chamber', Proc. IMechE, Part E: J. Process Mechanical Engineering, 2008, 222(E4), 211-223

Nilson, 1952: US Patent 2,622,787

Ohman H, 1999: US Patent

O'Neill P.A, 1993: Industrial Compressors, Theory and Equipment, Butterworth-Heinemann, Oxford

Peng N, Xing Z, 1990: 'New Rotor Profile and its Performance Prediction of Screw Compressor', International Compressor Engineering Conference At Purdue, 18

Rinder L, 1979: Schraubenverdichter (Screw Compressors), Springer Verlag, New York

Rinder L, 1984: 'Schraubenverdichterlaufer mit Evolventenflanken (Screw Compressor Rotor with Involute Lobes)', Proc. VDI Tagung "Schraubenmaschinen 84" VDI Berichte Nr. 521 Dusseldorf

Rinder L, 1987: US Patent 4,643,654

Sakun I.A, 1960: Vintovie kompresorii (Screw Compressors), Mashinostroenie Leningrad

Sauls J, 1998: 'An Analytical Study of the Effects of Manufacturing on Screw Rotor Profiles and Rotor Pair Clearances', Proc. VDI Tagung "Schraubenmaschinen 98", Dortmund VDI Berichte 1391

Shibbie, 1979: US Patent 4,140,445

Singh P.J, Onuschak A.D, 1984: 'A Comprehensive Computerized Method For Twin Screw Rotor Profile Generation and Analysis', Purdue Compressor Technology Conference 544

Singh P.J, Schwartz J.R, 1990: 'Exact Analytical Representation of Screw Compressor Rotor Geometry', International Compressor Engineering Conference At Purdue, 925

Smith I.K, Stosic N, 1995: 'The Expressor: An Efficiency Boost to Vapour Systes by Power recovery from the Throttlong Process', Proceedings of ASME Congress, Vol 34, November 1995 75. View the paper

Smith I.K, Stosic N, Aldis C.A, 1996: 'Development of the Trilateral Flash Cycle System: Part 1: Fundamental Considerations (doc), Part 2: Increasing Power Output with Working Fluid Mixtures (doc), Part 3: The Design of High-Efficiency Two-Phase Screw Expanders (doc) ', Proceedings of IMechE, Journal of Power and Energy, London, Vol 210, Part A, 75

Smith I.K, 1999: 'Review of the Development of Two-Phase Screw Expanders', Proceedings of IMechE, Conference 'Compressors and Their Systems, London, September 1999 75. View the paper

Smith I.K, Stosic N, Aldis C.A, Kovacevic A, 1999: 'Twin Screw Two-Phase Expanders in large Chiller Units', Proceedings of IMechE, Conference 'Compressors and Their Systems, London, September 1999 75. View the paper

Smith I.K, Stosic N. and Kovacevic A, 2001: 'Power Recovery From Low Cost Two-Phase Expanders', Geothermal Research Council 2001 Annual Meeting, San Diego, CA, August 2001. Download the paper (pdf)

Smith I.K, Stosic N. and Kovacevic A, 2001: 'A Feasibility Study of Throttle Loss Power Recovery in Large Heat Pums with Two-Stage Compressors',
IMechE Conference on Compressors and Their Systems, London, September 2001.

Smith I.K. and Stosic N, 2001: 'Prospects for Energy Conversion Efficiency Improvements by the Use of Two-Phase Expanders', 2nd International Heat Powered Cycles Conference, Paris, September 2001

Smith I.K, Stosic N, Kovacevic A, 2002: 'Twin Screw Machines to replace Throttle Valve in Refrigeration Systems', Strojniški Vestnik, Journal of Mechanical Engineering, 8 p 484, 2002

Smith I.K, Stosic N, Kovacevic A, 2004: 'An Improved System for Power Recovery from High Enthalpy Liquid Dominated Flows', GRC Annual Meeting, Indian Wells, California, August 2004

Smith I.K, Stosic N and Kovacevic A, 2005: 'An Improved System for Power Recovery from High Enthalpy Liquid Dominated Fields', World Geothermal Congress, Antalya Turkey, May 2005

Smith I.K, Stosic N, Kovacevic A, 2005: 'Screw Expanders Increase Output and Decrease the Cost of Geothermal Binary Power Plant Systems', GRC Annual Meeting, Reno, Nevada, September 2005. Download the paper (pdf)

Smith I.K, Stosic N, Kovacevic A, 2007: 'Cost Effective Small Scale ORC Systems for Power Recovery from Low Enthalpy Resources', GRC Annual Meeting, Reno, Nevada, September 2007. Download the paper (pdf)

Stosic N, Hanjalic K, 1977: 'Contribution towards Modelling of Two-Stage Reciprocating Compressors', Int.J.Mech.Sci. 19, 439

Stosic N, Hanjalic K, Koprivica J, Lovren N, Ivanovic M, 1986: 'CAD of Screw Compressor Elements', Strojarstvo Journal Zagreb 28, 181

Stosic N, Milutinovic Lj, Kovacevic A, Hanjalic K, 1992: 'Investigation of the Influence of Oil Injection upon the Screw Compressor Working Process', Int. J Refrig, Vol 15, 206. View the paper

Stosic N, Smith I.K, Zagorac S, 1996: 'CFD Studies of Flow in Screw and Scroll Compressors', Proc. XVIII Conference on Compressor Engineering at Purdue, 181

Stosic N., Hanjalic K., 1996: 'A General Method for Screw Compressor Profile Generation', Proc. XVIII Conference on Compressor Engineering at Purdue, 157

Stosic N, 1996: Patent Application GB 9610289.2

Stosic N, Hanjalic K, 1997: 'Development and Optimization of Screw Machines with a Simulation Model, Part I: Profile Generation', ASME Transactions, Journal of Fluids Engineering, Vol 119, p 659. View the paper

Stosic N, Smith I.K, Kovacevic A, Aldis C. A, 1997: 'The Design of a Twin-screw Compressor Based on a New Profile', Journal of Engineering Design, Vol 8, 389. View the paper

Stosic N, Smith I.K, Brasz J, Sishtla V, 1998: 'The Performance of a Screw Compressor with Involute Contact Rotors in a Low Viscosity Gas-Liquid Mixture Environment', Schraubenmaschinen '98, Dortmund, VDI Berichte 1391

Stosic N, 1998: 'On Gearing of Helical Screw Compressor Rotors', Proceedings of IMechE, Journal of Mechanical Engineering Science, London, Vol 212, Part C, 587. View the paper

Stosic N, Kovacevic A, Smith I.K, 2000: 'The CFD Analysis of a Screw Compressor Suction Flow', Proc. 2000 International Conference on Compressor Engineering at Purdue, 909

Stosic N, Smith I.K, Kovacevic A, Venumadhav K, 2000: 'Retrofit 'N' Rotors for Efficient Oil-Flooded Screw Compressors', Proc. 2000 International Conference on Compressor Engineering at Purdue, 917. Download the paper (pdf)

Stosic N, Smith I.K, and Kovacevic A, 2001: 'Rotor Interference as a Criterion in a Screw Compressors Design', ICTC, International Compressor Technique Conference, Wuxi, China, August 2001. Download the paper (pdf)

Stosic N, Smith I.K, and Kovacevic A, 2001: 'The design of efficient Screw Air Compressors', 3rd Symposium 'Revitalization and Modernization of Metal Industry in B&H, Bihac, Bosnia and Herzegovina, October 2001

Stosic N, Smith I.K, and Kovacevic A, 2002: 'A Twin Screw Combined Compressor and Expander for CO2 Refrigeration Systems', XVI International Compressor Engineering Conference at Purdue, July 2002. Download the paper (pdf)

Stosic N, Smith I.K, and Kovacevic A, 2002: 'Optimization of Screw Compressor Design', XVI International Compressor Engineering Conference at Purdue, July 2002

Stosic N, Smith I.K, and Kovacevic A, 2002: 'Optimization of Screw Compressor Design', VIII European Congress on Fluid Machinery for the Oil, Gas and Petrochemical Industry, October 2002. Download the paper (pdf)

Stosic N, Smith I.K, and Kovacevic A, 2002: 'Screw Compressor: A Strong Link in the Development Chain', 1st International Conference on Advanced Technologies for Developing Countries September 12-14, 2002 Slavonski Brod, Croatia

Stosic N, Smith I.K, Kovacevic A, 2002: 'Screw Compressor: A Strong Link in The Development Chain', Technical Gazette, Slavonski Brod, Vol 9, No 3,4, pp 41-46, 2002. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A, 2003: 'Rotor Interference as a Criterion for Screw Compressors Design', Journal of Engineering Design, Vol 14, No 2, pp 209-220, 2003

Stosic N, Smith I.K, Kovacevic A, 2003: 'The Design of Efficient Air Screw Compressors', Mašinstvo Journal, Zenica, 7(1) pp12-26, March 2003

Stosic N, Smith I.K, Kovacevic A, 2003: 'Optimisation of Screw Compressors', Journal of Applied Thermal Engineering, 23, pp 1177-1195, 2003. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A, 2004: 'Multifunctional Screw Machines', Mašinstvo Journal, Zenica, 8(1) pp 3-16, March 2004

Stosic N, Smith I.K, Kovacevic A, 2004: 'Opportunities for Innovation with Screw Compressors', Proceedings of IMechE, Journal of Process Mechanical Engineering, Vol 217, pp 157-170, 2003. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A, 2003: 'Improving Refrigeration Screw Compressor Performance with Optimised Rotors', IMechE International Conference on Compressors and Their Systems, London, September 8-10, 2003

Stosic N, Smith I.K, Kovacevic A, 2003: 'Combined Screw Compressor-Expander in Fuel Cell Application', IMechE International Conference on Compressors and Their Systems, London, September 8-10, 2003

Stosic N, Smith I.K, Kovacevic A, 2003: 'Multifunctional Screw Compressor Rotors', ICCR the 4th International Conference on Compressors and Refrigeration, Xi’an October 21-25, 2003. Download the paper (pdf)

Stosic N, 2004: 'Screw Compressors in Refrigeration and Air Conditioning', Int Journal of HVACR Research, 10(3) pp 233-263, July 2004. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A, 2004: 'Combined Compressor-Expander in Fuel Cell Application', COBEM 2003, 17th International Congress of Mechanical Engineers, Sao Paulo, November 10-14, 2003. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A, 2004: 'Identification of Heat Transfer on Screw Compressor Rotors as Tool for Their Design', HEFAT 2004, 3rd International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics 21-24 June 2004, Cape Town, South Africa

Stosic N, Smith I.K, Kovacevic A, 2004: 'Extension of Operating Range of Dry Screw Compressors by Cooling of Their Rotors', 17th International Compressor Engineering Conference at Purdue, July 2004

Stosic N, 2005: 'Tool Wear and Its Compensation in Screw Rotor Manufacturing', ACAM 2005, Australasian Congress on Applied Mechanics, 16-18 February 2005 Melbourne, Victoria, Australia. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A, 2005: Screw Compressors: Mathematical Modeling and Performance Calculation, Monograph, Springer Verlag, Berlin, June 2005, ISBN: 3-540-24275-9. Purchase the monograph

Stosic N, 2005: 'Identification of Constraints in the Optimal Generation of Screw Compressor Rotors by the Pressure Angle Method', IMechE International Conference on Compressors and Their Systems, London, September 5-7, 2005. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A, Jung-uk K, Park J, 2005: 'Improving screw compressor performance', IMechE International Conference on Compressors and Their Systems, London, September 5-7, 2005. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A, 2005: 'Numerical Investigation of Heat Transfer on Screw Compressor Rotors', 8th Argentinian Congress on Computational Mechanics, Buenos Aires, Argentina, November 2005. Download the paper (pdf)

Stosic N, Smith I.K, Kovacevic A and Zhang W M, 2005: 'An Investigation of Liquid Injection in Refrigeration Screw Compressors', ICCR the 5th International Conference on Compressors and Refrigeration, Dalian, July 2005

Stosic N, Mujic E, Kovacevic A, Smith I.K, 2006: 'The Influence of Discharge Ports on Rotor Contact in Screw Compressors', 18th International Compressor Engineering Conference at Purdue, July 2006. Download the paper (pdf)

Stosic N, 2006: 'Increasing the Reliability of Screw Compressors in the Gas and Process Industries', Oil & Gas Processing Review, London 2006. Download the paper (pdf)

Stosic N, 2006: 'A geometric approach to calculating tool wear in screw rotor machining', International Journal of Machine Tools & Manufacture 46, 1961–1965

Stosic N, 2006: 'Evaluating errors in screw rotor machining by tool to rotor transformation', Proc. IMechE Vol. 220, Part B: J. Engineering Manufacture, pp 1589-1596

Stosic N, Kovacevic A, Mujic E, Smith I.K, 2006: 'Vacuum and Multiphase Screw Pump Rotor Profiles and Their Calculation Models', Schraubencompressortagung, Dortmund, VDI Berichte 1932, September 2006

Stosic N, Broglia T and Iobbi M, 2006: 'Improving the Capacity and Performance of Air-Conditioning Screw Compressors', IMECE 2006, ASME Congress, Chicago, November 2006. Download the paper (pdf)

Stosic N, Kovacevic A, Mujic E, Smith I.K, 2007: 'Development of a Rotor Profile for Silent Screw Compressor Operation', International Conference Compressors and Their Systems, London, 2007. Download the paper (pdf)

Stosic N, Kovacevic A, Mujic E, Smith I.K, 2007: 'An Evaluation of Encapsulated Oil Flooded Screw Compressor Systems', IMECE2007, ASME Congress, Seattle, November 2007. Download the paper (pdf)

Stosic N, Mujic E, Kovacevic A, Smith I.K, 2008: 'Profiling of Screw Compressor Rotors by Use of Direct Digital Simulation', International Compressor Engineering Conference at Purdue, July 2008. Download the paper (pdf)

Stosic N, Smith I.K, Mujic E, Kovacevic A, 2008: 'Geometry of Screw Compressor Rotors and Their Tools', ICCR 2008, International Conference on Compressor and Refrigeration, Xian, September 2008. Download the paper (pdf)

Stosic N and Smith I.K, 2008: 'Utilization of Expansion Work in Transcritical CO2 Heat Pumps in Combined Heating and Cooling', Proceedings of IMECE2008, 2008 ASME International Mechanical Engineering Congress and Exposition, Boston, USA, November 2-6, 2008,

Venu Madhav K, Stosic N, Smith I.K, and Kovacevic A, 2001: 'The Design of a Family of Screw Compressors for Oil–Flooded Operation', IMechE Conference on Compressors and Their Systems, London, September 2001. Download the paper (pdf)

Venu Madhav K, Stosic N, Smith I.K, Kovacevic A, 2003: Proektirovanie semeistva maslozapolneniih vintoviih kompressorov Compressors and Pneumatics, Vol 1 pp 2-5, 2003

Tang Y, Fleming J.S, 1992: 'Obtaining the Optimum Geometrical Parameters of a Refrigeration Helical Screw Compressor', International Compressor Engineering Conference at Purdue 213

Tang Y, Fleming J. S, 1994: 'Clearances between the Rotors of Helical Screw Compressors: Their determination, Optimization and Thermodynamic Consequences', Proceedings of IMechE, Journal of Process Mechanical Engineering, Vol 208, 155

Tang Y. and Fleming J. S, 1994: 'Obtaining the Optimum Geometrical Parameters of a Refrigeration Helical Screw Compressor', XI International Compressor Engineering Conference at Purdue, July 1992, pp 221-227

Xion Z. Dagang X, 1986: 'Study on Actual Profile Surface and Engaging Clearance of Screw Compressor Rotors', Purdue Compressor Technology Conference 239

Xing Z. W, 2000: Screw Compressors, Machine Press, Beijing

Zhang L, Hamilton J.F, 1992: 'Main Geometric Characteristics of the Twin Screw Compressor', International Compressor Engineering Conference at Purdue 213

Zhang W, Wang Z, Stosic N, Mujic E, Kovacevic A, Smith I.K, 2006: 'New Design and Rotor Retrofit to Improve Capacity and Performance of Refrigeration Screw Compressors', 18th International Compressor Engineering Conference at Purdue, July 2006. Download the paper (pdf)